Original data and independent reporting for the HVAC trade

Pellet Stove Not Igniting? Find the Failed Start-Up Step and the Maker’s Code

Homeowner cleaning the burn pot of a pellet stove not igniting

A pellet stove not igniting has failed at one of three start-up steps: no pellets reach the burn pot (empty or bridged hopper, open lid switch, vacuum switch not proving draft, stuck auger), pellets arrive but do not light (dead igniter, blown fuse, plugged burn pot holes, wet fuel), or it lit but the control never sensed the fire.

Watch one start-up and answer in order1. Exhaust blower startswhen you press ON?NODead stove: outlet, breaker, boardfuse, tripped high limit resetYES2. Igniter glows redwithin 3 to 5 minutes?NOIgniter element, igniter fuse or noboard output. Napoleon: 30 to 50 ohmsYES3. Pellets drop intothe burn pot?NOEmpty or bridged hopper, lid switch,vacuum switch not proving, auger jamYES4. Pellets catch inabout 15 minutes?NOPlugged burn pot holes or ignitertube, wet pellets, damper too openYESLit, then shut down after 20 to 30 minutes:heat sensor or proof of fire switch never saw the fire (E-2 on Englander)
Checks in the order the stove performs them. Timings: England’s Stove Works 25-EP and 25-PDVC manuals; igniter resistance: Napoleon NPS40 manual. Drawn by The HVAC Brief.

What should a pellet stove do in the first 15 minutes after you press ON?

The exhaust blower starts at once, the igniter glows within about 3 to 5 minutes, the auger feeds, and the fire should be established by about 15 minutes. The first step that does not happen is your fault.

England’s Stove Works says the 25-EP should show “the red glow of the igniter” after three to five minutes and be “burning brightly” after approximately fifteen minutes. Its 25-PDVC has a 13 minutes start-up cycle, and pressing ON a second time restarts it from zero. Napoleon’s NPS40 chart shuts the blower off on a unit that “failed to reach 140°F within 15 minutes.” So let a cold stove finish the cycle; restarting early piles pellets in the pot, and Englander says to clean them out before any manual restart “to prevent over-feeding.”

Which maker code or blink pattern matches what your stove is doing?

Codes differ by brand and even by series: E-1 means vacuum loss on the Englander 25-PDVC, while the 25-EP manual says “This error code is not used on this stove.” Match the row to your model plate.

Compiled by The HVAC Brief from five maker manuals. Each row applies only to the model named.
What you see Code, model Causes the maker lists Check
Nothing runs No lights, Lennox Winslow PS40 Outlet dead, board fuse blown Breaker; 3 amp board fuse
Blower runs, igniter never glows No code, Drolet Eco 45 Igniter fuse, bad element, no board output F3 fuse, 5 Amp 250V
Igniter glows, auger never turns No code, Englander 25-PDVC Hopper lid switch, clogged “door ajar” port, vacuum sensor Latch lid; clear port right of burn pot
Stove shuts itself off E-1 Vacuum Loss, Englander 25-PDVC; 1 short and 1 long blink, Lennox Winslow PS40 Blocked flue, blower failure, door or ash drawer not sealing, plugged vacuum hose Gaskets, hose, vent
Pellets fed, no flame Constant red, ignite light 2 short blinks, Lennox Winslow PS40 Hopper empty, auger tube not full, burn pot holes plugged, igniter 6 amp igniter fuse; pot holes
Lit, then quit after 20 to 30 minutes E-2 Fail to Start, Englander 25-PDVC Loose heat sensor, low start setting, igniter buildup Start on “5” to “9”
Fire went out mid-burn E-4, Englander 25-EP Proof of flame lost, usually empty hopper Refill, press ON once
Pellets can bridge in the hopper and stop feeding even when the hopper is full.
Pellets can bridge in the hopper and stop feeding even when the hopper is full. AI illustration.

Why is my pellet stove not dropping pellets when the igniter is glowing?

On the stoves in our set, a safety interlock (lid switch or vacuum switch) is holding the feed off, or the auger is stuck. A dropped latch or a small air leak stops the feed while the igniter keeps glowing.

The 25-PDVC hopper lid safety switch (part AC-HLSB) is wired straight to the top auger motor, and Englander says a faulty one means “a top auger that will not turn and therefore a stove that will not burn.” The “door ajar” vacuum port right of the burn pot “must be kept clean, or the top auger will cease to function”; clear it with a pipe cleaner, stove unplugged and cool. Englander’s “Auger not turning” row adds a loose set screw, a bad gear motor, foreign matter and carbon in the feed tube. Its pre-2004 25-PDVC manual says pellets that “bridge in the hopper” drop the heat chamber below 90 degrees and trigger shutdown, as if fuel ran out.

The 25-EP dry-run test isolates the lid switch: hold it down and the auger should turn; release it and the auger should stop. Keep fingers out of the hopper, and never tape the switch or jumper a vacuum switch: Englander says the lid switch keeps combustion byproducts from entering the home.

Does E-1 on an Englander pellet stove mean the vacuum switch is bad?

Not necessarily. On the 25-PDVC, E-1 means the switch stopped seeing draft, and the manual lists power failure, combustion blower failure, a blocked flue (rodents, nests, soot), improper flue installation and dirty burning ahead of a bad switch.

The switch reads firebox suction through a small hose, so any leak trips it: the 25-PDVC stops feeding if the door is open about two minutes, and Englander says to “check for loose or cracked vacuum hose” and to replace the 3/4 inch door rope gasket annually. Lennox lists door seal, ash drawer seal, restricted passageways, vent pipe and a plugged hose ahead of “vacuum switch defective” on the Winslow PS40. A technician will measure firebox draft and check whether the switch closes under suction; if the blower cannot pull enough vacuum, the vent is the fault. If the stove also puffs smoke, the house-pressure side is on our wood stove smoking into house page.

Clogged burn pot holes starve the igniter of air, so pellets drop but never light.
Clogged burn pot holes starve the igniter of air, so pellets drop but never light. AI illustration.

Pellets drop but don’t light: is the igniter dead?

Check it last. Drolet and Lennox list a plugged burn pot, blocked igniter tube or over-open damper ahead of a failed element, and a blown igniter fuse looks exactly like a dead igniter.

Drolet’s Eco 45 chart starts with the air damper “open too far for ignition,” then a blocked igniter tube, then the element: on direct power the tip should glow “after about 2 minutes.” It also lists the F3 igniter fuse (5 Amp 250V) and a board sending no power. Lennox uses a 6 amp igniter fuse on the Winslow PS40; Englander says to “check igniter for buildup.”

Unplugged, a meter across the igniter leads reads resistance. Napoleon publishes the number for the NPS40: “30Ω to 50Ω (± 3Ω),” checked before fitting a new start-up timer because a shorted ignitor can kill it. Other cartridges differ, so use your own manual’s figure, and leave live line-voltage checks to a technician.

Why won’t my pellet stove light after cleaning it?

Usually a part went back in wrong: Napoleon’s NPS40 checks start with whether “the burn pot is positioned properly,” and Englander says a 25-PDVC wear plate must lie flat with “no gaps (from ash residue)” under it.

Englander warns that “ash build-up under the wear plate can cause the unit to malfunction,” and allows a 1/8 inch drill bit to reopen glazed burn pot air holes. Its schedule: scrape the pot daily, remove ash twice each week, pull the 12 by 13 inch baffle monthly. Then confirm the door and ash pan latch fully, since a leak trips the vacuum switch.

Can wet or low-grade pellets stop a pellet stove from lighting?

Yes. Englander’s 25-PDVC chart lists “excessive pellet moisture” and “low quality pellets” behind a lazy fire, and says high-ash or wet pellets fill the burn pot faster.

Under 40 CFR 60.532(e), certified pellet heaters may burn only pellets named in the owner’s manual and graded by an EPA-approved third party: the Pellet Fuels Institute, ENplus or CANplus. Englander asks for 1/4 inch pellets stored dry so they stay “pelletized and low in moisture content.” Fuel rules and costs are on our wood and pellet stove rules page.

Why won’t a pellet stove light after a power outage?

Most treat a long outage as OFF. The Englander 25-PDVC resumes on its own only after an outage of three minutes or less; longer than that, it waits for you to press ON.

During the outage, Englander says not to open the hopper lid or door (“This may cause fire to burn in the hopper”) and to open an outside door and a window so smoke is not pulled into the room. Its chart lists a 6 AMP fuse blown by a power surge as a cause of a dead stove. Clear unburned pellets from the pot, press ON once, and if a code returns, call the maker rather than cycling it. Because the stove needs electricity, it ranks low on ways to keep a house warm during a power outage without backup power. Any vented combustion appliance needs a CO alarm nearby; see our carbon monoxide detector placement rules.

Frequently asked questions

Do pellet stoves have a reset button?

Some do. Drolet’s Eco 45 has an L-250 manual-reset high temperature switch with a red button on the back, and Lennox says the Winslow PS40 snap switch reset must be pushed before the stove will run. Englander 25-PDVC owners clear an E-code by pressing ON only once. A high limit that trips again means overheating to find.

Can I light a pellet stove by hand if the igniter is not working?

On some models. The Englander 25-PDVC manual allows it: clear the burn pot, add a handful of pellets, light them with wax chips or pellet fire starter, then close the door and press ON. Close the door too early and the exhaust blower can blow the fire out. Never use gasoline, kerosene or lighter fluid.

Why is my pellet stove not blowing hot air?

On the Englander 25-PDVC the chart blames a loose sensor or a high “ON” temperature setting when the room air blower never starts. On the Lennox Winslow PS40, a convection blower that is not running can trip the over temperature snap switch (2 long blinks) and shut the stove down.

Why is my pellet stove not getting enough air?

Lennox lists a door or ash drawer that is not sealing, restricted flue passageways and a restricted vent pipe for the Winslow PS40. Englander says 25-PDVC burn pot air holes must stay clear (a 1/8 inch drill bit is allowed) and the baffle plate comes out monthly so ash does not choke the exhaust path.

How we researched this

Research date: 20 November 2026. We read the start-up, code and troubleshooting sections of the England’s Stove Works 25-PDVC (current and pre-2004) and 25-EP manuals, the Lennox Winslow PS40, Drolet Eco 45 and Napoleon NPS40 manuals, and 40 CFR 60.532. Codes apply only to the model named. Forums, videos and retailer blogs were excluded as figure sources. We cut leads on igniter temperatures, a 40 to 80 ohm igniter range and PFI moisture and ash limits because no primary document we opened states them. No repair prices appear.

Sources

  1. England’s Stove Works. “Installation & Operation Manual, Models 25-PDVC / 25-PDVCH / 55-SHP10.” https://cdn.shopify.com/s/files/1/0782/2077/files/25PVD.pdf. Accessed November 2026.
  2. England’s Stove Works. “Installation and Operation Manual, Models 25-PDVC, 55-SHP10 and 55-TRP10 (pre-2004 units).” https://cdn.shopify.com/s/files/1/2071/6041/files/pre-04.25-PDVC.pdf. Accessed November 2026.
  3. England’s Stove Works. “Installation & Operation Manual, 25-EP / 55-SHPEP / 55-TRPEP (Rev. 8/2008),” archived copy. https://archive.org/download/manualsonline-id-fcdcecfd-feff-4a48-affd-6def39e9c420/fcdcecfd-feff-4a48-affd-6def39e9c420.pdf. Accessed November 2026.
  4. Lennox Hearth Products. “Winslow PS40 manual, Diagnostic Codes, p. 25.” https://auto.manualsonline.com/manuals/mfg/lennox_hearth/lennox_hearth_freestanding_pellet_stove_model_winslowtm_ps40.html?p=25. Accessed November 2026.
  5. Drolet. “Eco 45 manual, Troubleshooting Guide, p. 21.” https://laundry.manualsonline.com/manuals/mfg/drolet/eco45.html?p=21. Accessed November 2026.
  6. Napoleon. “NPS40 manual W415-0616, Troubleshooting, p. 40.” https://fitness.manualsonline.com/manuals/mfg/napoleon_fireplaces/nps40.html?p=40. Accessed November 2026.
  7. eCFR. “40 CFR 60.532.” https://www.ecfr.gov/current/title-40/chapter-I/subchapter-C/part-60/subpart-AAA/section-60.532. Accessed November 2026.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *