Why is my mini split blinking? Most often for a normal reason: it is defrosting or warming its coil in heat mode, flagging that power was cut, or refusing a mode another zone already holds. A fixed count that repeats after a pause, with the unit stopped, is a fault code, and the timer lamp tells you which half to suspect.

Which lamp is blinking, and is the mini split still running?
Check which lamp is blinking and whether the head still moves air. A slow blink on the Operation, Heat or Defrost lamp in heat mode, on a cold day, with the fans stopped, is defrost on every brand we checked. Fujitsu’s AST series manual says heat stops “between 7 and 15 minutes” while the OPERATION lamp flashes slowly, and Gree’s Livo R32 service manual lists the heat indicator flashing once every 10 seconds as “Not error code”.
Carrier’s 40MAQ DEFROST indicator lights “when the coil is warming up to prevent cold blow”. If ice keeps returning, our heat pump defrost cycle explainer covers how often a normal cycle runs.
Which blinks do Carrier, Daikin, Mitsubishi, Fujitsu, MRCOOL, Senville, Gree and LG call normal?
Every maker below documents at least one blink that is not a fault; rule those out first. Read only the row for your series: the Fujitsu row comes from the older AST7 and AST9 manual plus a Fujitsu General FAQ, and newer Fujitsu boards count differently, as our Fujitsu blink code tables show.
| Brand and document | Blinks the maker calls normal | Blinks the maker calls a fault | How to read it |
|---|---|---|---|
| Carrier 40MAQ, Bryant 619PB | Operation flashes once per second after power is on. Two dashes: STANDBY on a multi zone in AUTO. | Operation flashes 1 to 7 times; Timer off, lit or flashing sets the family. EC with lamps flashing: refrigerant leak. | Count flashes, note Timer |
| Daikin FTXR-T, FTX-N | FTXR-T color is the mode (Orange TIMER, Blue COOL). Lamp blinks twice to confirm a timer. | Operation lamp blinks: protection device, thermistor or transmission error. | Timer Cancel, 5 seconds |
| Mitsubishi MSZ-GL | Multi system head in a clashing mode blinks. | Upper lamp blinks 2 to 14 or more times, then 2.5 seconds off. | Count 2 cycles |
| Fujitsu AST7, AST9 | Slow flash in defrost; 1 second on, 1 second off when a mode cannot be used; lamps alternate after a power cut. | TIMER lamp flashing: breaker off, call service. | Count both lamps |
| MRCOOL DIY 4th Gen | 1 Operation flash, Timer ON, two dashes: mode conflict. | Timer OFF: EH, EL, EC codes. Timer FLASH: PC codes. | Read the display |
| Senville AURA multi zone | Operation light flashes when power returns; blocked head flashes rapidly. | Display code | Read the display |
| Gree Livo R32 | Heat indicator flashes once every 10 seconds in defrost: “Not error code”. | Temperature indicator blinks the error code. | Gree code table |
| LG, North America | None listed | Blinking LED1 (Heating LED) and LED2 (Cooling LED). | Count both LEDs |
The LG row carries a warning: LG Canada’s page says North American units signal codes with blinking LEDs, but its examples disagree on which LED is the tens digit, which our LG blink count page works through.

Why is my mini split blinking after a power outage?
Because many heads are built to tell you power was interrupted and wait for a button press. Fujitsu General’s FAQ 0084 says the operation and timer lamps “blink alternately” when power is interrupted during operation, and that both blink together during a test run. Senville’s AURA manual says “the Operation light on the indoor unit will flash” when power returns and the ON/OFF button restarts it.
Carrier’s OM-40MAQ-07 owner’s manual says the OPERATION indicator “flashes once per second after power is on”, and Auto Start resumes the stored settings. The same manual says the compressor will not start for 3 to 4 minutes after a stop. If the breaker trips again, our guide to a system that will not restart after an outage lists what to check.
Why does one head on a multi zone mini split blink or show two dashes?
One outdoor unit cannot heat one room and cool another, so the head that asked second is parked. Mitsubishi’s MSZ-GL service manual OBH732 says the mode of the indoor unit that operates first is selected, and the “other indoor units cannot operate, and operation indicator lamp blinks”. Fujitsu says units operated afterward stop and the red OPERATION lamp flashes when heating meets cooling, dry or fan.
Heads with a display show it as characters instead. Carrier’s 40MAQ manual says AUTO changeover on a multi zone “could set an indoor unit to STANDBY mode, indicated with two dashes” and that “HEATING is the system’s priority mode”. MRCOOL’s 4th Gen manual lists 1 Operation flash with the Timer lamp on as “Indoor units mode conflict”. Senville gives heat mode precedence, and the blocked head’s operation light will flash rapidly. The fix: set every head to one mode, and keep AUTO for single zone systems, as Carrier recommends.
What does a blinking timer light mean on a Carrier or Bryant mini split?
On a Carrier 40MAQ, a flashing Timer lamp alongside a flashing Operation lamp points to an inverter or power protection code, the P family. Carrier’s 40MAQ service manual sorts every indoor display code by the Timer lamp state,, the fastest way to separate indoor from outdoor faults on a head with no display.
| Timer lamp | Operation lamp flashes | Codes in that family | What Carrier lists |
|---|---|---|---|
| Off | 1 to 7 | E0, E1, E2, E3, E4, E5, EC | Indoor side: board memory, communication (E1), fan speed, T1 and T2 sensors, refrigerant leak (EC) |
| Lit steady | 1 to 6 | F0, F1, F2, F3, F4, F5 | Outdoor side: overload current (F0), T3, T4 and T5 sensors, outdoor memory, outdoor fan |
| Flashing | 1, 2, 3 or 5 | P0, P1, P2, P4 | Inverter and power: IPM overcurrent (P0), over or under voltage (P1), compressor top temperature (P2), compressor drive (P4) |
Bryant’s 619PB shares Carrier’s owner’s manual OM38-40MA-02 with the 40MAQ; confirm the table against your model’s service manual before buying parts. MRCOOL’s 4th Gen also puts PC codes on a flashing Timer lamp, but PC 00 and PC 03 both flash 7 times, so read the display; our MRCOOL code page sorts those by generation.
For P1, Gree’s service manual has the technician measure L to N and flags supply above 265 VAC or below 150 VAC; Daikin’s flowchart checks supply within ±10% of rated.
Is a Daikin blinking green, blue or orange light a fault?
The color is not the fault; the blink is. On FTXR-T heads the multi-monitor lamp shows the mode (Blue COOL, Red HEAT, Green DRY, White FAN, Red/Blue AUTO, Orange TIMER), so a blinking blue lamp is a fault that happened in cooling. The manual also says the lamp blinks twice to confirm a timer setting. On FTX-N heads the operation lamp is green, and Daikin’s FTX-N service manual says it blinks for a protection device, a thermistor or a transmission error.
To read the code, hold Timer Cancel for 5 seconds until 00 shows; our Daikin error code page lists the presses for each code.
How do you count the blinks, and what will the technician measure?
Count two full cycles before touching the breaker, because a power cycle can hide the code. Mitsubishi tells technicians to “check at least 2 consecutive blinking cycles”, each group separated by 2.5 seconds off. Its 5 blink code means the compressor stopped 3 times within 1 minute after startup; a nonstop 0.5 second blink means no serial signal from the outdoor unit for 6 minutes. Our Mitsubishi blink count page covers the rest.
Stop at the cover. A refrigerant leak code (Carrier and MRCOOL EC, MRCOOL EL 0C) needs a technician with gauges, and finding the leak is the work in our refrigerant leak detection guide. Carrier’s service manual warns that electricity “is kept in capacitors even if the power supply is shut off”, so inverter codes stay with the technician, who will check supply voltage, the indoor to outdoor wiring at the terminal board (Daikin’s U4 flowchart measures between terminals No. 1 and No. 3), and whether the outdoor board LED blinks.
Frequently asked questions
Why is my Carrier mini split red light blinking?
The Carrier 40MAQ owner’s manuals we read name the indicators but give no colors, so identify the lamp by its label. If it is Operation with the unit stopped, count the flashes and check whether Timer is off, lit or flashing; Carrier’s Table 10 splits those into E, F and P codes.
Why is my Daikin mini split power light blinking?
On Daikin FTX-N and FTXR-T wall units the operation lamp blinks when a protection device trips, a thermistor fails or the indoor and outdoor units stop talking. Read the code before cutting power: hold Timer Cancel on the remote for 5 seconds until 00 shows, then step through codes until a long beep.
Why is my Bryant mini split blinking dashes?
Carrier’s 40MAQ manual says AUTO on a multi zone system can put an indoor unit into STANDBY, shown as two dashes, until every head runs the same mode, with HEATING as the priority. Bryant’s 619PB shares the 40MAQ owner’s manual OM38-40MA-02. Set every head to the same mode; Carrier describes the dashes, not a blink.
How long does a mini split blink in defrost mode?
Fujitsu’s AST series manual says heat stops for between 7 and 15 minutes while the OPERATION lamp flashes slowly. Senville’s AURA manual gives 4 to 10 minutes, and Mitsubishi says a head started during defrost can take max. 10 minutes to blow warm air. Gree’s Livo flashes the heat indicator once every 10 seconds.
How we researched this
In November 2026 we read the 12 documents in Sources (Carrier, Daikin, Mitsubishi, Fujitsu, MRCOOL, Senville, Gree and LG manuals or support pages) in full text, plus the Gree Livo owner’s manual. We read the top ranking pages for this query and used none as a source. Pioneer is excluded because we did not open a Pioneer lamp manual for this page; lamp colors appear only where a maker states them.
Sources
- Carrier. “40MAQ / 38MAQ, 619PB / 538PR Owner’s Manual (OM38-40MA-02).” https://www.shareddocs.com/hvac/docs/1009/Public/0F/OM38-40MA-02.pdf. Accessed November 2026.
- Carrier. “40MAQ High Wall Ductless System Owner’s Manual (OM-40MAQ-07).” https://www.shareddocs.com/hvac/docs/1009/Public/09/OM-40MAQ-07.pdf. Accessed November 2026.
- Carrier. “40MAQ High Wall Ductless System Service Manual (40MAQ-01SM).” https://www.shareddocs.com/hvac/docs/1009/Public/00/40MAQ-01SM.pdf. Accessed November 2026.
- Daikin. “Service Manual, Wall Mounted Type FTXR-T Series (SiUS041829EA).” https://resource.ecmdi.com/is/content/Watscocom/Gemaire/daikin_rx-rmvju9_en_sm.pdf. Accessed November 2026.
- Daikin. “Service Manual, Wall Mounted Type FTX-N Series (SiUS091601E).” https://st.storeland.ru/11/2207/818/FTX_FVXS_series_Service_Manual.pdf. Accessed November 2026.
- Mitsubishi Electric. “Service Manual MSZ-GL, MSY-GL (OBH732).” https://resource.bakerdist.com/is/content/Watscocom/Gemaire/mitsubishi_msz-gl06na-u1_article_1458549065594_en_sm.pdf. Accessed November 2026.
- Fujitsu. “Operating Manual, Wall Mounted Type AST7 and AST9 Series (archived copy).” https://archive.org/download/manualsonline-id-f6bd4c27-1e12-41a3-9b5a-99ef4dd4babf/f6bd4c27-1e12-41a3-9b5a-99ef4dd4babf.pdf. Accessed November 2026.
- Fujitsu General. “FAQ 0084: indicator lamps on the indoor unit blink.” https://www.fujitsu-general.com/th/en/support/faq/split/0084.html. Accessed November 2026.
- MRCOOL. “DIY E Star 4th Gen Installation and Owner’s Manual.” https://www.mrcool.com/wp-content/dox_repo/mc-diy-4-es-im-um-en-01.pdf. Accessed November 2026.
- Senville. “AURA Multi Zone Owner’s Manual.” https://www.sylvane.com/cdn/shop/files/owners-manual-senville-aura-48000-btu-dual-zone-mini-split-heat-pump.pdf. Accessed November 2026.
- Gree. “Livo R32 Service Manual.” https://www.greecomfort.com/assets/our-products/livo-r32/documents/livo-r32-service-manual-a.pdf. Accessed November 2026.
- LG Electronics Canada. “Single/Multi Split Air Conditioner Error Codes.” https://www.lg.com/ca_en/support/product-support/troubleshoot/help-library/cs-CT30000386-20153289364119/. Accessed November 2026.

Leave a Reply