MRCOOL mini split error codes depend on the generation: DIY Gen 1 to 3 show two characters (E1, P4, EC), while 4th and 5th Gen show four (EL 01, PC 04, EL 0C). DF, AP, CL, FP and FC are status displays, not faults. PC 03 is pressure protection.
Which MRCOOL displays are not faults: DF, AP, CL, FP, FC?
None of those five is a fault. MRCOOL’s Advantage 5th Gen manual marks them “Normal Display, not error code”, yet the DIY 5th Gen manual lists them under “Error Display” with no such label, and the help center code table leaves them out. Defrost timing is on our heat pump defrost cycle page.
| Display | MRCOOL’s meaning | What the unit is doing | What to do |
|---|---|---|---|
| DF or dF | Defrost | Melting outdoor coil frost. DIY 5th Gen ends a cycle on coil temperature or at 15 minutes. | Clear snow. Wait. |
| cF | Anti-cold-air in HEAT | Holding the fan until the coil warms, up to 30 minutes on DIY units. | Wait. |
| CL, Cl or SC | Active Clean; SC is Self Clean on DIY 3rd Gen | Freezing and thawing the indoor coil. CL stops itself after 20 to 45 minutes. | Let it finish. |
| CL, nF at power on | Filter reminders (Advantage 5th Gen) | Shows for 15 seconds. | Clean or replace the filter. |
| FP | Heating with the room under 46.4°F | Keeping the room above about 46°F for pipes. | Nothing, if set on purpose. |
| FC | Forced cooling | Force Start pressed twice. Cools for 30 minutes, then auto at 76°F. | Press Force Start again. |
| AP | AP mode of Wi-Fi connection | Waiting to pair with the app. | Finish pairing. |
| CP | Remote switched off | Label only in the manuals. | Ask MRCOOL. |
| 00 | Standby | Waiting for input. | Change mode; check remote batteries. |
Compiled by The HVAC Brief from MRCOOL manuals and support articles.

What do PC 03, EL 0C, E1 and the other MRCOOL fault codes mean?
Each fault has a two-character and a four-character name; MRCOOL’s article titles pair them. One master list ranking today gives E1 as an indoor air sensor, E5 as communication and F4 as low pressure. MRCOOL’s Gen 1 to 3 table says communication, coil sensor T2 and outdoor EEPROM.
| Gen 1 to 3 | 4th and 5th Gen | MRCOOL’s meaning | First check, then what a technician measures |
|---|---|---|---|
| E1 | EL 01 | Indoor and outdoor units not communicating | Matching wiring, no splices. DC volts across terminals 2 and 3 swing from minus 25 V to plus 25 V. Fixed points indoors, positive only outdoors. |
| EC | EL 0C | Refrigerant leak detected; on 5th Gen, system lacks refrigerant | New: no threads showing, Allen key valves open. Existing: leak search, charge, T2 ohms. |
| P6 on some charts | PC 03 | Pressure protection | PC 03 section below. |
| P4 | PC 04 | Inverter compressor drive error | Valves open, connections tight, board burns. Then winding ohms at the T plug. |
| P0, P1 | PC 00, PC 01 | IPM malfunction; over or under voltage | About 240 V at L1 and L2 on 230 V units, 120 V at L and N on 115 V. |
| P2 | PC 02 | Compressor top or IPM high temperature | Clean the outdoor coil. Then gauges. |
| F0 | PC 08 | Current overload | Voltage, loose terminals. |
| P3 | PC 0L | Outdoor temperature too low | Warmer weather clears it. Check the sensor wire for ice. |
| E3 | EH 03 | Indoor fan speed out of range | Breaker off; blower wheel should spin freely. |
| E4, E5 | EH 60, EH 61 | Room sensor T1, coil sensor T2 | Sensor and plug. |
| F1, F2, F3 | EC 53, EC 52, EC 54 | Outdoor ambient, coil, discharge sensors | Sensor and plug, outdoors. |
| F5 | EC 07 | Outdoor fan speed out of range | Fan motor or a loose board wire. |
| E0, E2, F4 | EH 00, EH 02, EC 51 | EEPROM or zero-crossing error | Voltage, burn marks; may need a board. |
| 88 | 88 | Solid: power or control board. Flashing with Wi-Fi symbol: wiring | Solid: 15 minute reset. Flashing: wires 2 and 3 swapped. DIY puts white on 2, Advantage black. |
| None | EH C1, EH C2, EC C1 | Refrigerant sensor detected a leak | EH C1 section below. |
| None | EH C3, FH CC | Refrigerant sensor out of range or failed | Maker’s sensor only. |
| Double dash | Double dash | Multi-zone mode conflict | One mode on all zones. Heating has priority. |
Compiled by The HVAC Brief from MRCOOL’s hub table, manuals and per-code articles.
MRCOOL’s articles start most of these with the breaker off 15 minutes. The DIY 4th Gen manual warns against attempting the repairs yourself, and live metering is qualified work. Symptoms without a code are on our mini split repair page.
Which table fits DIY Gen 3, 4th Gen, 5th Gen, Advantage, Olympus or Universal?
Start from where the code appears: MRCOOL publishes separate indoor and outdoor tables.
| Product line | Code set and quirk |
|---|---|
| DIY Gen 1 to 3 | E, F, P, EC. Multi-zone outdoor board uses other meanings. |
| DIY 4th Gen, Advantage 4th Gen | EH, EL, EC, PC. Lamp flashes carry the code, but PC 00 and PC 03 share 7 flashes. |
| DIY 5th Gen, DIY Select, Easy Pro 5th Gen, Advantage 5th Gen, Olympus 4th Gen | Adds FH and refrigerant sensor codes. PC 03 is low or high pressure. |
| OuttaSight ceiling cassette | EH 0E is the water-level switch: clear the drain line. |
| Olympus ceiling cassette | Article lists E1 to P8; service manual lists EH, EL, PC. Trust your display. |
| Universal Series (ducted) | Its own table. 08 is defrosting. Air handlers blink. |
Compiled by The HVAC Brief from 14 MRCOOL manuals.

Why does P6 or AP mean something else on another MRCOOL unit?
MRCOOL reuses characters across lines. P6 has four meanings below, plus low pressure in the PC03/P6 article, and the Universal Series list makes E1 a pressure trip. Pioneer changed its code meanings between generations as well, so the same characters read differently on current units and on the discontinued Quantum WYS line, as the Pioneer mini split error codes show.
| Display | Gen 1 to 3 indoor | Gen 1 to 3 multi-zone outdoor board | Universal |
|---|---|---|---|
| E1 | Communication | Not listed | High pressure (condenser), low pressure (packaged) |
| E5 | Coil sensor T2 | Over or under voltage | Not listed |
| P0 | IPM malfunction | Compressor top temperature | Drive reset protection |
| P6 | Refrigerant amount (hub), discharge sensor (DIY 3rd Gen manual) | IPM malfunction | Main control to drive communication |
| AP | Wi-Fi pairing (5th Gen manuals) | Not listed | Fan AC input voltage abnormality (packaged) |
Compiled by The HVAC Brief from MRCOOL’s hub, DIY 3rd Gen manual, Universal list.
The Advantage 5th Gen manual prints EH OA with a letter O, and EH 06 where other 5th Gen manuals print EH 0B. Zone Air’s lookup site says 4th Gen displays alternate a code’s two halves; no MRCOOL document we read confirms it, so watch for both. Mitsubishi has the same trap in another form, since each of its series prints its own table of Mitsubishi mini split error codes.
Is PC 03 a refrigerant leak on a pre-charged DIY line set?
Not automatically. On a new install, MRCOOL’s PC03 article starts with: no threads showing, service valves opened to the locking ring, and on multi-zone units (excluding dual zone Gen 4) king valves open. It also suggests lightly tapping a stuck pressure switch, breaker off. On an existing install it sends you to a professional.
The DIY 4th Gen manual defines PC 03 as low pressure; the DIY 5th Gen service manual says low or high. That switch trips above 638 PSI or below 18.85 PSI, and the outdoor board separates them as PC 30 and PC 31. The technician reads gauges against those limits and tests the switch: a healthy low pressure protector reads 0 ohms (4th Gen manual). Adding refrigerant is not an owner fix; our DIY mini split page covers EPA’s line-connection rule.
What is the difference between EL 0C and EH C1?
EL 0C is inferred from running data; EH C1 is a sensor reading gas in the room. MRCOOL’s EL0C article blames low charge most often, then closed valves, and rarely the T2 sensor. Senville AURA and LETO units carry a matching low refrigerant code, listed with the other Senville mini split error codes.
The DIY 5th Gen manual warns of fire risk if R-454B leaks near an ignition source, says to remove open flames, and says the unit must stay powered except for service. Call a technician; our refrigerant leak detection guide compares methods. One false trigger: MRCOOL says uncured Great Stuff spray foam vapor can cause EH-C1, cleared by holding SW1 for 10 seconds.
How long do you power cycle a MRCOOL mini split before a code counts as real?
Wait about 10 minutes, then cut power. MRCOOL’s 3rd, 4th and 5th Gen manuals say the problem may resolve itself in that time. Gree splits its list the same way, naming codes that may clear after a restart and codes that need a technician, as the Gree mini split error codes show. Its support articles use 15 minutes at the breaker, as the reset and to de-energize before reaching inside. A P3/PC0L lockout will not clear until the outdoors warms; our cold climate heat pump page compares limits.
Frequently asked questions
What does C1 mean on a MRCOOL mini split?
No MRCOOL mini split table we read has a standalone C1 row. It is most likely the second half of EH C1 (refrigerant sensor detects leakage) or EC C1 (another indoor unit’s sensor, multi-zone). The only standalone C1 row in MRCOOL’s help center is GeoCool: return air temperature sensor error.
What does flashing AP mean on a MRCOOL mini split?
AP means access point mode, ready to join home Wi-Fi through the MRCOOL app. MRCOOL says the code disappears once connected and names three checks if it does not: Wi-Fi strength, resetting the module and the credentials. On the Universal packaged unit, AP means fan AC input voltage abnormality.
What does EL OC mean on a MRCOOL mini split?
It is EL 0C, and the third character is a zero in MRCOOL’s tables. The 5th Gen manuals call it system lacks refrigerant. The DIY 4th Gen manual calls it refrigerant leak detected and also prints it once as ELOC.
Why does my MRCOOL show PC 0L when it is not that cold?
MRCOOL’s PC0L article says the condenser can sit colder than the air. Its documents also disagree on the limit: the P3/PC0L article says minus 13°F, while the DIY 5th Gen service manual says minus 31°F compressor off and minus 40°F running, clearing at minus 25.6°F. In milder weather, check the outdoor sensor wire.
How we researched this
We read 14 MRCOOL manuals as PDFs and more than 40 help center articles through its public article feed, because the pages block automated fetches. Where they conflict, we show both. Retailer and contractor charts were excluded as sources. We tested no unit. Research date: November 5, 2026.
Sources
- MRCOOL Support. “Mini Split Systems Error Codes.” https://support.mrcool.com/hc/en-us/articles/39803744782868-Mini-Split-Systems-Error-Codes. Accessed November 2026.
- MRCOOL Support. “Per-code articles and product pages: AP, DF, FC, FP, cF, 88, spray foam, Olympus cassette, E0/EH00 to F5/EC-07.” https://support.mrcool.com/hc/en-us. Accessed November 2026.
- MRCOOL. “DIY 5th Gen Manual.” https://doxrepo.mrcool.com/mc-diy-5-sz-im-um-en-01.pdf. Accessed November 2026.
- MRCOOL. “DIY 5th Gen Service Manual.” https://doxrepo.mrcool.com/mc-diy-5-sz-sm-en-01.pdf. Accessed November 2026.
- MRCOOL. “Advantage 5th Gen Manual.” https://doxrepo.mrcool.com/mc-adv-5-im-en-01.pdf. Accessed November 2026.
- MRCOOL. “DIY 4th Gen Manual.” https://www.mrcool.com/wp-content/dox_repo/mc-diy-4-es-im-um-en-01.pdf. Accessed November 2026.
- MRCOOL. “DIY 3rd Gen Manual.” https://www.mrcool.com/wp-content/dox_repo/mc-diy-3-es-im-um-en-01.pdf. Accessed November 2026.
- MRCOOL. “Olympus Cassette Service Manual.” https://doxrepo.mrcool.com/mc-oly-mz-4g-cass-sm-en-01.pdf. Accessed November 2026.
- MRCOOL Support. “PC03/P6 Error Code.” https://support.mrcool.com/hc/en-us/articles/29008362911892-PC03-P6-Error-Code-DIY-Troubleshooting. Accessed November 2026.
- MRCOOL Support. “EC or EL0C Error Codes.” https://support.mrcool.com/hc/en-us/articles/30667612886676-Troubleshooting-EC-or-EL0C-Error-Codes-on-MRCOOL-Mini-Split-Systems. Accessed November 2026.
- MRCOOL Support. “Error Codes: Universal Series.” https://support.mrcool.com/hc/en-us/articles/37024354722196-Error-Codes-Universal-Series. Accessed November 2026.
- MRCOOL Support. “P3/PC0L Error Code.” https://support.mrcool.com/hc/en-us/articles/31237036660756-Troubleshooting-a-P3-PC0L-Error-Code-on-a-MRCOOL-Mini-Split-System. Accessed November 2026.

Leave a Reply