Original data and independent reporting for the HVAC trade

·

MRCOOL Mini Split Error Codes by Generation, and the Displays That Are Not Faults

Homeowner and technician checking mrcool mini split error codes at a wall-mounted indoor unit

MRCOOL mini split error codes depend on the generation: DIY Gen 1 to 3 show two characters (E1, P4, EC), while 4th and 5th Gen show four (EL 01, PC 04, EL 0C). DF, AP, CL, FP and FC are status displays, not faults. PC 03 is pressure protection.

Which MRCOOL displays are not faults: DF, AP, CL, FP, FC?

None of those five is a fault. MRCOOL’s Advantage 5th Gen manual marks them “Normal Display, not error code”, yet the DIY 5th Gen manual lists them under “Error Display” with no such label, and the help center code table leaves them out. Defrost timing is on our heat pump defrost cycle page.

Display MRCOOL’s meaning What the unit is doing What to do
DF or dF Defrost Melting outdoor coil frost. DIY 5th Gen ends a cycle on coil temperature or at 15 minutes. Clear snow. Wait.
cF Anti-cold-air in HEAT Holding the fan until the coil warms, up to 30 minutes on DIY units. Wait.
CL, Cl or SC Active Clean; SC is Self Clean on DIY 3rd Gen Freezing and thawing the indoor coil. CL stops itself after 20 to 45 minutes. Let it finish.
CL, nF at power on Filter reminders (Advantage 5th Gen) Shows for 15 seconds. Clean or replace the filter.
FP Heating with the room under 46.4°F Keeping the room above about 46°F for pipes. Nothing, if set on purpose.
FC Forced cooling Force Start pressed twice. Cools for 30 minutes, then auto at 76°F. Press Force Start again.
AP AP mode of Wi-Fi connection Waiting to pair with the app. Finish pairing.
CP Remote switched off Label only in the manuals. Ask MRCOOL.
00 Standby Waiting for input. Change mode; check remote batteries.

Compiled by The HVAC Brief from MRCOOL manuals and support articles.

Pressure faults on a mini split are traced at the outdoor unit's service valves and flare connections.
Pressure faults on a mini split are traced at the outdoor unit's service valves and flare connections. AI illustration.

What do PC 03, EL 0C, E1 and the other MRCOOL fault codes mean?

Each fault has a two-character and a four-character name; MRCOOL’s article titles pair them. One master list ranking today gives E1 as an indoor air sensor, E5 as communication and F4 as low pressure. MRCOOL’s Gen 1 to 3 table says communication, coil sensor T2 and outdoor EEPROM.

Gen 1 to 3 4th and 5th Gen MRCOOL’s meaning First check, then what a technician measures
E1 EL 01 Indoor and outdoor units not communicating Matching wiring, no splices. DC volts across terminals 2 and 3 swing from minus 25 V to plus 25 V. Fixed points indoors, positive only outdoors.
EC EL 0C Refrigerant leak detected; on 5th Gen, system lacks refrigerant New: no threads showing, Allen key valves open. Existing: leak search, charge, T2 ohms.
P6 on some charts PC 03 Pressure protection PC 03 section below.
P4 PC 04 Inverter compressor drive error Valves open, connections tight, board burns. Then winding ohms at the T plug.
P0, P1 PC 00, PC 01 IPM malfunction; over or under voltage About 240 V at L1 and L2 on 230 V units, 120 V at L and N on 115 V.
P2 PC 02 Compressor top or IPM high temperature Clean the outdoor coil. Then gauges.
F0 PC 08 Current overload Voltage, loose terminals.
P3 PC 0L Outdoor temperature too low Warmer weather clears it. Check the sensor wire for ice.
E3 EH 03 Indoor fan speed out of range Breaker off; blower wheel should spin freely.
E4, E5 EH 60, EH 61 Room sensor T1, coil sensor T2 Sensor and plug.
F1, F2, F3 EC 53, EC 52, EC 54 Outdoor ambient, coil, discharge sensors Sensor and plug, outdoors.
F5 EC 07 Outdoor fan speed out of range Fan motor or a loose board wire.
E0, E2, F4 EH 00, EH 02, EC 51 EEPROM or zero-crossing error Voltage, burn marks; may need a board.
88 88 Solid: power or control board. Flashing with Wi-Fi symbol: wiring Solid: 15 minute reset. Flashing: wires 2 and 3 swapped. DIY puts white on 2, Advantage black.
None EH C1, EH C2, EC C1 Refrigerant sensor detected a leak EH C1 section below.
None EH C3, FH CC Refrigerant sensor out of range or failed Maker’s sensor only.
Double dash Double dash Multi-zone mode conflict One mode on all zones. Heating has priority.

Compiled by The HVAC Brief from MRCOOL’s hub table, manuals and per-code articles.

MRCOOL’s articles start most of these with the breaker off 15 minutes. The DIY 4th Gen manual warns against attempting the repairs yourself, and live metering is qualified work. Symptoms without a code are on our mini split repair page.

Which table fits DIY Gen 3, 4th Gen, 5th Gen, Advantage, Olympus or Universal?

Start from where the code appears: MRCOOL publishes separate indoor and outdoor tables.

Where is the code showing?Indoor head displayOutdoor control boardUniversal air handlerCopy every characterEL then 0C is one code.0 is a zero, not O.Then pick a row below.Separate board tableGen 1 to 3 multi-zone:P6 is IPM, E5 is voltage.4th and 5th Gen: PC 30high, PC 31 low pressure.Count flashes per 3 s1: jumper cap2: indoor fan4: tube sensorDF, AP, CL, FP, FC, CP, cF, SCStatus display, not a faultE1, EC, P4, F0: two charactersDIY Gen 1 to 3 tableEL 01, PC 03, EH 60: four characters4th or 5th Gen tableEH C1, EH C2, EC C1Refrigerant sensor alarm: see below
Sources: MRCOOL help center tables, DIY 5th Gen service manual, Universal Series list.
Product line Code set and quirk
DIY Gen 1 to 3 E, F, P, EC. Multi-zone outdoor board uses other meanings.
DIY 4th Gen, Advantage 4th Gen EH, EL, EC, PC. Lamp flashes carry the code, but PC 00 and PC 03 share 7 flashes.
DIY 5th Gen, DIY Select, Easy Pro 5th Gen, Advantage 5th Gen, Olympus 4th Gen Adds FH and refrigerant sensor codes. PC 03 is low or high pressure.
OuttaSight ceiling cassette EH 0E is the water-level switch: clear the drain line.
Olympus ceiling cassette Article lists E1 to P8; service manual lists EH, EL, PC. Trust your display.
Universal Series (ducted) Its own table. 08 is defrosting. Air handlers blink.

Compiled by The HVAC Brief from 14 MRCOOL manuals.

A defrost cycle is normal in cold weather, which is why some display codes are status messages, not faults.
A defrost cycle is normal in cold weather, which is why some display codes are status messages, not faults. AI illustration.

Why does P6 or AP mean something else on another MRCOOL unit?

MRCOOL reuses characters across lines. P6 has four meanings below, plus low pressure in the PC03/P6 article, and the Universal Series list makes E1 a pressure trip. Pioneer changed its code meanings between generations as well, so the same characters read differently on current units and on the discontinued Quantum WYS line, as the Pioneer mini split error codes show.

Display Gen 1 to 3 indoor Gen 1 to 3 multi-zone outdoor board Universal
E1 Communication Not listed High pressure (condenser), low pressure (packaged)
E5 Coil sensor T2 Over or under voltage Not listed
P0 IPM malfunction Compressor top temperature Drive reset protection
P6 Refrigerant amount (hub), discharge sensor (DIY 3rd Gen manual) IPM malfunction Main control to drive communication
AP Wi-Fi pairing (5th Gen manuals) Not listed Fan AC input voltage abnormality (packaged)

Compiled by The HVAC Brief from MRCOOL’s hub, DIY 3rd Gen manual, Universal list.

The Advantage 5th Gen manual prints EH OA with a letter O, and EH 06 where other 5th Gen manuals print EH 0B. Zone Air’s lookup site says 4th Gen displays alternate a code’s two halves; no MRCOOL document we read confirms it, so watch for both. Mitsubishi has the same trap in another form, since each of its series prints its own table of Mitsubishi mini split error codes.

Is PC 03 a refrigerant leak on a pre-charged DIY line set?

Not automatically. On a new install, MRCOOL’s PC03 article starts with: no threads showing, service valves opened to the locking ring, and on multi-zone units (excluding dual zone Gen 4) king valves open. It also suggests lightly tapping a stuck pressure switch, breaker off. On an existing install it sends you to a professional.

The DIY 4th Gen manual defines PC 03 as low pressure; the DIY 5th Gen service manual says low or high. That switch trips above 638 PSI or below 18.85 PSI, and the outdoor board separates them as PC 30 and PC 31. The technician reads gauges against those limits and tests the switch: a healthy low pressure protector reads 0 ohms (4th Gen manual). Adding refrigerant is not an owner fix; our DIY mini split page covers EPA’s line-connection rule.

What is the difference between EL 0C and EH C1?

EL 0C is inferred from running data; EH C1 is a sensor reading gas in the room. MRCOOL’s EL0C article blames low charge most often, then closed valves, and rarely the T2 sensor. Senville AURA and LETO units carry a matching low refrigerant code, listed with the other Senville mini split error codes.

EL 0C: inferred from running dataEH C1: measured in room airCompressor startsBoard tracks coil sensor T2Refrigerant sensor in the headReads gas concentrationCheck fails 3 timesin the first 5 minutes (4th Gen)10% LFL or more for 10 secondsor 20% LFL or moreCode shows, unit turns offLow charge, closed valve or T2Compressor stops, indoor fan runsBuzzer sounds. Spray foam can fake it
Sources: MRCOOL DIY 4th Gen manual section 10.7; DIY 5th Gen service manual TS06-N10 and manual item 15; spray foam article.

The DIY 5th Gen manual warns of fire risk if R-454B leaks near an ignition source, says to remove open flames, and says the unit must stay powered except for service. Call a technician; our refrigerant leak detection guide compares methods. One false trigger: MRCOOL says uncured Great Stuff spray foam vapor can cause EH-C1, cleared by holding SW1 for 10 seconds.

How long do you power cycle a MRCOOL mini split before a code counts as real?

Wait about 10 minutes, then cut power. MRCOOL’s 3rd, 4th and 5th Gen manuals say the problem may resolve itself in that time. Gree splits its list the same way, naming codes that may clear after a restart and codes that need a technician, as the Gree mini split error codes show. Its support articles use 15 minutes at the breaker, as the reset and to de-energize before reaching inside. A P3/PC0L lockout will not clear until the outdoors warms; our cold climate heat pump page compares limits.

Frequently asked questions

What does C1 mean on a MRCOOL mini split?

No MRCOOL mini split table we read has a standalone C1 row. It is most likely the second half of EH C1 (refrigerant sensor detects leakage) or EC C1 (another indoor unit’s sensor, multi-zone). The only standalone C1 row in MRCOOL’s help center is GeoCool: return air temperature sensor error.

What does flashing AP mean on a MRCOOL mini split?

AP means access point mode, ready to join home Wi-Fi through the MRCOOL app. MRCOOL says the code disappears once connected and names three checks if it does not: Wi-Fi strength, resetting the module and the credentials. On the Universal packaged unit, AP means fan AC input voltage abnormality.

What does EL OC mean on a MRCOOL mini split?

It is EL 0C, and the third character is a zero in MRCOOL’s tables. The 5th Gen manuals call it system lacks refrigerant. The DIY 4th Gen manual calls it refrigerant leak detected and also prints it once as ELOC.

Why does my MRCOOL show PC 0L when it is not that cold?

MRCOOL’s PC0L article says the condenser can sit colder than the air. Its documents also disagree on the limit: the P3/PC0L article says minus 13°F, while the DIY 5th Gen service manual says minus 31°F compressor off and minus 40°F running, clearing at minus 25.6°F. In milder weather, check the outdoor sensor wire.

How we researched this

We read 14 MRCOOL manuals as PDFs and more than 40 help center articles through its public article feed, because the pages block automated fetches. Where they conflict, we show both. Retailer and contractor charts were excluded as sources. We tested no unit. Research date: November 5, 2026.

Sources

  1. MRCOOL Support. “Mini Split Systems Error Codes.” https://support.mrcool.com/hc/en-us/articles/39803744782868-Mini-Split-Systems-Error-Codes. Accessed November 2026.
  2. MRCOOL Support. “Per-code articles and product pages: AP, DF, FC, FP, cF, 88, spray foam, Olympus cassette, E0/EH00 to F5/EC-07.” https://support.mrcool.com/hc/en-us. Accessed November 2026.
  3. MRCOOL. “DIY 5th Gen Manual.” https://doxrepo.mrcool.com/mc-diy-5-sz-im-um-en-01.pdf. Accessed November 2026.
  4. MRCOOL. “DIY 5th Gen Service Manual.” https://doxrepo.mrcool.com/mc-diy-5-sz-sm-en-01.pdf. Accessed November 2026.
  5. MRCOOL. “Advantage 5th Gen Manual.” https://doxrepo.mrcool.com/mc-adv-5-im-en-01.pdf. Accessed November 2026.
  6. MRCOOL. “DIY 4th Gen Manual.” https://www.mrcool.com/wp-content/dox_repo/mc-diy-4-es-im-um-en-01.pdf. Accessed November 2026.
  7. MRCOOL. “DIY 3rd Gen Manual.” https://www.mrcool.com/wp-content/dox_repo/mc-diy-3-es-im-um-en-01.pdf. Accessed November 2026.
  8. MRCOOL. “Olympus Cassette Service Manual.” https://doxrepo.mrcool.com/mc-oly-mz-4g-cass-sm-en-01.pdf. Accessed November 2026.
  9. MRCOOL Support. “PC03/P6 Error Code.” https://support.mrcool.com/hc/en-us/articles/29008362911892-PC03-P6-Error-Code-DIY-Troubleshooting. Accessed November 2026.
  10. MRCOOL Support. “EC or EL0C Error Codes.” https://support.mrcool.com/hc/en-us/articles/30667612886676-Troubleshooting-EC-or-EL0C-Error-Codes-on-MRCOOL-Mini-Split-Systems. Accessed November 2026.
  11. MRCOOL Support. “Error Codes: Universal Series.” https://support.mrcool.com/hc/en-us/articles/37024354722196-Error-Codes-Universal-Series. Accessed November 2026.
  12. MRCOOL Support. “P3/PC0L Error Code.” https://support.mrcool.com/hc/en-us/articles/31237036660756-Troubleshooting-a-P3-PC0L-Error-Code-on-a-MRCOOL-Mini-Split-System. Accessed November 2026.

Comments

3 responses to “MRCOOL Mini Split Error Codes by Generation, and the Displays That Are Not Faults”

  1. […] E9 beside 6841, U1 beside 1302. Letter codes are brand-specific, so do not borrow meanings from our MRCOOL code tables or the Daikin mini split […]

  2. […] own article titles it EH 0b. Codeless leaks and iced coils are in the mini split repair guide; MRCOOL mini split error codes use the same […]

  3. […] PC codes on a flashing Timer lamp, but PC 00 and PC 03 both flash 7 times, so read the display; our MRCOOL code page sorts those by […]

Leave a Reply

Your email address will not be published. Required fields are marked *